24+ YEARS EXPERIENCE | FULLY LICENSED | FULLY INSURED
Get an instant ballpark for your driveway, patio, sidewalk, or steps project anywhere in NYC. Enter your dimensions below — no email required.
Planning a concrete project in New York City. Use the calculator above to get an instant cost range for your driveway, patio, sidewalk, or steps based on your dimensions and borough. Below, we break down exactly what goes into concrete pricing across NYC so you know what to expect before you call a contractor.
Concrete work in New York City typically costs between 9 and 16 dollars per square foot installed, depending on project type, thickness, site access, and borough. A standard 20×10 foot driveway section runs roughly 1,800 to 3,200 dollars, while a small sidewalk flag replacement can run lower. Material alone, if you are ordering ready mix without labor, averages 150 to 200 dollars per cubic yard.
The calculator takes four inputs: project type, length and width, slab thickness, and borough. From there, it calculates your total square footage, converts that into cubic yards of concrete needed, and applies current NYC installed pricing to give you a low and high range.
The tool is built for quick planning, not a final quote. It does not account for demolition of an existing slab, base preparation, drainage work, or reinforcement needs, all of which affect your final number. Think of it as a starting point before you request a free estimate from our team.
Project type, thickness, site access, and existing conditions determine your final cost more than anything else. A few factors move the number up or down from the baseline estimate:
A typical NYC driveway costs between 3,600 and 6,500 dollars for a standard 20×20 foot slab, depending on thickness, reinforcement, and site conditions. Larger driveways or those requiring extensive demolition and regrading for drainage can run higher.
Most residential driveways are poured at 4 inches for standard car weight, or 6 inches if the driveway will see heavier vehicles or regular use. If your current driveway already shows cracking or sinking, it is worth reading through how to fix a cracked concrete driveway before deciding between a patch job and a full replacement, since the extent of the damage usually determines which route makes more financial sense.
For projects planned through the winter months, our guide on the best driveway materials for cold weather in NY covers why reinforced concrete with an air entrained mix holds up better against freeze thaw cycles than asphalt alternatives.
Sidewalk replacement in NYC generally runs on the lower end of the per square foot range, though total cost depends heavily on the length of frontage and whether a DOT violation is involved. Property owners are legally responsible for the sidewalk in front of their building, and the city inspects for hazards under DOT rules.
If you received a violation notice, cracks wider than half an inch, height differences of half an inch or more between slabs, or missing and broken sections typically trigger the citation. Our sidewalk violation removal service handles the repair and manages inspection sign off so the violation clears from your record. For general wear without a notice, sidewalk repair covers trip hazard correction and slab leveling before the damage becomes a compliance issue.
Anyone adding a new curb cut as part of a sidewalk or driveway project should also check how to get a curb cut permit in NYC, since DOB and DOT both need to sign off before work begins.
Patios and general slabs tend to fall at the lower to middle end of the per square foot range since they carry less structural load than a driveway. A standard 4 inch pour is usually sufficient for a patio, and the finish (broom, stamped, or exposed aggregate) is often the bigger cost driver rather than the base structural work.
If you are set on a paver look instead of a poured slab, our paver installation service covers patios, walkways, and driveways with the grading and base prep needed to prevent shifting over time.
Steps and stoops cost more per square foot than flatwork because of the formwork, reinforcement, and finishing labor involved in building each riser and tread. Most stoops are poured at 6 inches or more for structural strength, which the calculator accounts for automatically when you select steps as your project type.
Combination projects, brick stoops with concrete steps, or masonry repair alongside a new pour, are common in older NYC buildings. If your stoop involves brick or mortar work, porch repair and brick pointing may be worth pairing with your concrete estimate.
Yes, borough location shifts pricing slightly due to site access, parking restrictions, and permit turnaround times, though material and base labor costs stay consistent citywide. Manhattan projects tend to run higher because of limited truck access and street permitting. Brooklyn falls slightly above the citywide average in denser neighborhoods. Queens, the Bronx, and Staten Island generally see the most standard pricing with easier site access.
We serve all five boroughs directly. You can find borough specific project examples and service details on our Queens, Manhattan, Brooklyn, and Bronx contractor pages.
No. The calculator gives a planning range based on square footage and standard NYC installed pricing. Your final cost depends on demolition needs, base condition, drainage, and reinforcement, which is why we always recommend a free on-site visit before locking in a number.
The per square foot range reflects a fully installed project, meaning material, labor, forming, and standard finishing. It does not include demolition of an existing slab, permit fees, or major site prep like regrading for drainage.
The calculator converts your square footage and thickness into cubic yards automatically. For reference, a 20×10 foot slab at 4 inches thick works out to roughly 0.9 cubic yards. Most residential jobs are ordered through ready mix delivery rather than bagged concrete once the volume passes about half a yard.
Most driveway, sidewalk, and curb work requires DOB and DOT permits. As a licensed and insured concrete contractor, we handle the permit process and inspections as part of every project so you do not have to manage the paperwork yourself.
Concrete reaches initial strength within 24 to 48 hours and is typically ready for light foot traffic shortly after. Full cure takes about 28 days, though driveways can usually handle vehicle weight sooner depending on the mix and weather conditions during the pour.
Site access and permit complexity vary by borough. Tight lots and limited parking in Manhattan, for example, slow down delivery and pouring compared to a Queens or Staten Island property with a standard driveway, which is reflected in the estimate.
This calculator gives you a starting point. For a precise number based on your property, contact Hi Tech Construction NY or call (718) 600-4676 for a free on-site estimate. Most quotes are provided within 48 hours, and our team handles permits, inspections, and the full project from start to finish.